Revision of Installing Trisquel on a server from Sat, 08/08/2009 - 19:16

The 2.x robur LTS version of Trisquel is a very good choice for a server: it has a 64 bit version -needed for 4GB+ RAM, and recommended for virtualization-, a server-optimized linux-libre kernel, and a Xen linux-libre kernel as well.

We are working in a netinst image, wich will allow you to install a server using a small and handy iso image with a full featured installer which downloads the needed packages from the desired Trisquel mirror. In the meantime, you can use this howto to manually install a clean server environment.

You will need...

• A Trisquel 2.x CD. Any of them should should do, we recommend you to use a i386 image to build a 32 bit server and a amd64 to build a 64 bit one.

• A server with compatible hardware. You can use almost any x86/x86_64 server, but take care not to buy parts with no free drivers, as they will not work.

• Some skills about managing a Debian based server. If you are a newbie, install the edu edition with the included installer and use it as a server -with the desktop environment-.

Starting

Start a Live CD session in your server -we recommend to start in in English-. Open a terminal. All the commands listed below will be run in that terminal.

Partition and format your disk

You can partition a disk in a lot of ways and using different hardware configurations. For the purposes of this howto, we will assume that you are installing Trisquel in a single and empty SATA/SCSI disk with no RAID.

NOTE: We will refer to the disk as /dev/sda

Start the partition manager cfdisk. If you like to start with an empty layout, use this command:

sudo cfdisk -z

You can partition your disk using the layout of your choice, but we recommend this one:

DEVICE     MOUNTPOINT   FILESYSTEM    SIZE
/dev/sda1  /            ext3          5GB
/dev/sda2  swap         swap          1.5 times the memory size
/dev/sda3  /tmp         XFS           1GB
/dev/sda4  /home        XFS           the rest of the disk

Notes:

• The swap is optional, it will be needed if you want to have suspend-to-disk support.
• Never use XFS for the partition containing /boot
• Having /tmp in a partition will keep the server from crashing by fullness.

So, use cfdisk to break the disk into that pieces, and save. Now to format the partitions, use this commands:

sudo mkswap /dev/sda1
sudo mkfs.ext3 /dev/sda2
sudo mkfs.xfs /dev/sda3
sudo mkfs.xfs /dev/sda4

This is just a example layout, you can use the one that fits your needs.

Mount the disk

Create a mountpoint:

sudo mkdir /target

Now mount the root (/) partition into /target

sudo mount /dev/sda2 /target

Install the base system

You will use debootstrap to download and install a trisquel base environment. You will need to update the Live CD apt lists and install it first:

sudo aptitude update
sudo aptitude install debootstrap

Some usefull parameters that you can give to debootstrap are the arch (it will use the same as the Live CD if you don't give it one), and the mirror (it defaults to archive.trisquel.info, located in Spain):

sudo debootstrap --arch=amd64 trisquel /target http://us.archive.trisquel.info

Configure the base system

You will need to configure your installation, and the first step is to fill the /target/etc/apt/sources.list file. You can just copy the file from the Live CD or use this contents:

# Trisquel repositories for supported software and updates
deb http://archive.trisquel.info/trisquel robur main extras
deb-src http://archive.trisquel.info/trisquel robur main extras
deb http://archive.trisquel.info/trisquel robur-updates main extras
deb-src http://archive.trisquel.info/trisquel robur-updates main extras
deb http://archive.trisquel.info/trisquel robur-security main extras
deb-src http://archive.trisquel.info/trisquel robur-security main extras

The backports repo is not recommended in a server. You can replace archive.trisquel.info with the mirror of your choice.

Now enter in the chroot:

sudo chroot /target

You should now be able to update your apt lists and install packages. This is a list of recommended commented commands to run:

# set the server hostname and hosts file
echo boxname > /etc/hostname
echo "127.0.0.1 localhost" > /etc/hosts
echo "127.0.0.1 boxname" > /etc/hosts

# set the root password
passwd

# mount /proc
mout none /proc -t proc

# set up your dns config, replace the ip with your dns server.
echo "nameserver 192.168.1.1" > /etc/resolv.conf

# configure the keyboard
dpkg-reconfigure console-setup

# update the apt lists
aptitude update

# install a linux-libre kernel image and boot loader package
aptitude install linux-image-server grub

# copy the grub files to /boot and run the grub config updater
cp /usr/lib/grub/* /boot/grub -a
update-grub

# If you prefer to have bash instead of dash as default shell, run this:
dpkg-reconfigure dash

# umount /proc
umount /proc

# exit the chroot
exit

Install the boot loader

sudo grub-install --no-floppy --root-directory=/mnt/target /dev/sda

Edit the fstab

You need to edit the /target/etc/fstab file according to the disk layout you made. This is the fstab file that matches our suggested selections:

#<file system> <mount point>   0    1       2  3
 proc          /proc           proc      defaults        0       0
 none          swap            sw        defaults        0       0
 /dev/sda2     /               ext3      relatime        0       1
 /dev/sda3     /tmp            xfs       relatime        0       2
 /dev/sda4     /home           xfs       relatime        0       2

You can now reboot and login into your new Trisquel server!

What to do next?

Your new server is an empty shell. You will need to install whatever you need in your box. Here are some handy suggestions:

Install a Xen environment

This is an easy one, you just need to add a package:

aptitude install trisquel-server-xen

Build a GLAMP server

To serve web pages, the most common web server is apache. If you don't need php or a database, just type this:

aptitude install apache2

To get a complete GLAMP (GNU/Linux Apache MySQL PHP) server, use this:

aptitude install apache2 mysql-server phpmyadmin

That will install all the needed dependencies, and will also allow you to manage your database by login into http://localhost/phpmyadmin