Error Broadcom

Por lo que veo en el dmesg tu tarjeta es una Intel 3945 a/b/g , desconozco
si estas tarjetas están soportadas por Trisquel , esta tarjeta puede
funcionar con dos drivers , el ipw3945 (deprecated) y el iwlwifi. Todo será
ver que tipo de licencias usan los drivers ( y sobre todo los firmwares ,
que son los que dan más problemas con este tema)

Un saludo.

El 18 de septiembre de 2009 01:26, <name at domain> escribió:

> Buenas tardes, al instalar trisquel no me reconoce mi tarjeta inalámbrica,
> agradecería si me pueden ayudar.
>
> Los detalles de la maquina son: Compaq nx7400 con tarjeta inalámbrica:
> Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02).
>
> El error que arroja por el dmesg es:
> [ 9.559847] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
> [ 9.559859] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) ->
> IRQ 16
> [ 9.559952] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [ 9.820505] Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID:
> FW13 ]
> [ 9.832740] lp0: using parport0 (interrupt-driven).
> [ 9.937042] Adding 1959888k swap on /dev/sda5. Priority:-1 extents:1
> across:1959888k
> [ 10.891292] kjournald starting. Commit interval 5 seconds
> [ 10.892345] EXT3 FS on sda1, internal journal
> [ 10.892350] EXT3-fs: mounted filesystem with ordered data mode.
> [ 10.954967] XFS mounting filesystem sda7
> [ 11.281444] Ending clean XFS mount for filesystem: sda7
> [ 11.445020] iwl3945: Radio Frequency Kill Switch is On:
> [ 11.445022] Kill switch must be turned off for wireless networking to
> work.
> [ 11.586502] type=1505 audit(1253228923.713:2): operation="profile_load"
> name="/sbin/dhclient-script" name2="default" pid=2072
> [ 11.586656] type=1505 audit(1253228923.713:3): operation="profile_load"
> name="/sbin/dhclient3" name2="default" pid=2072
> [ 11.586700] type=1505 audit(1253228923.713:4): operation="profile_load"
> name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default"
> pid=2072
> [ 11.586742] type=1505 audit(1253228923.713:5): operation="profile_load"
> name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2072
> [ 11.713563] type=1505 audit(1253228923.841:6): operation="profile_load"
> name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2077
> [ 11.713754] type=1505 audit(1253228923.841:7): operation="profile_load"
> name="/usr/sbin/cupsd" name2="default" pid=2077
> [ 14.704543] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> [ 14.704546] Bluetooth: BNEP filters: protocol multicast
> [ 14.721120] Bridge firewalling registered
> [ 17.478741] [drm] Initialized drm 1.1.0 20060810
> [ 17.494936] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> [ 17.494942] pci 0000:00:02.0: setting latency timer to 64
> [ 17.495101] [drm] Initialized i915 1.6.0 20080730 on minor 0
> [ 17.496778] [drm:i915_setparam] *ERROR* unknown parameter 4
> [ 17.496805] [drm:i915_getparam] *ERROR* Unknown parameter 6
> [ 18.806192] [drm:i915_getparam] *ERROR* Unknown parameter 6
> [ 19.873593] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 19.875217] 0000:10:00.0: Missing Free firmware
> [ 19.875223] iwl3945 0000:10:00.0: firmware: requesting /*(DEBLOBBED)*/
> [ 19.894843] iwl3945: /*(DEBLOBBED)*/ firmware file req failed: Reason
> -22
> [ 19.894848] iwl3945: Could not read microcode: -22
> [ 23.804175] b44: eth0: Link is up at 100 Mbps, full duplex.
> [ 23.804179] b44: eth0: Flow control is off for TX and off for RX.
> [ 23.804477] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 34.408009] eth0: no IPv6 routers present
> [ 35.206955] [drm:i915_getparam] *ERROR* Unknown parameter 6
>
>
> Gracias anticipadas por la ayuda...
>
> Gerardo Figueroa
> www.lestat.org.ve
> _______________________________________________
> Trisquel-usuarios mailing list
> name at domain
> http://listas.trisquel.info/cgi-bin/mailman/listinfo/trisquel-usuarios
>

--
unzip, strip, touch, finger, mount, fsck, more, yes, unmount, sleep - my
daily Unix command list