Problem when installing Trisquel in external HDD

15 risposte [Ultimo contenuto]
Megver83
Offline
Iscritto: 12/21/2015

It´s a 1TB Toshiba HDD, it connects with a 3.0 usb cable. I already installed Trisquel on a 32 GB pendrive (usb 3.0 too) and worked, so I said "cool, now with the Toshiba external HDD" but.... as sth. had to go bad.
It´s not a problem with the partitions, but during installation in the terminal interface that shows the progress it appears me a message like a thousand times:

(date)(time) trisquel kernel (...) reset full speed usb device number 2 using uhci_hcd
(date)(time) trisquel kernel (...) parent hub missing LPM exit latency info. Power management will be impacted.

So I´m like "yea yea, bla bla...." but the progress bar stucks in the middle.

The (...) represents some numbers without importance.

*NOTE: This same post is in the spanish forum, just put this because in the spanish forum seems that some people have few time.

Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

The HDD may be defective. You can self-test it by selecting it in "Disks" (in the "System settings") and using the related entry in the menu (the button with a gear in the upper-right corner of the window).

amenex
Offline
Iscritto: 01/03/2015

Magic Banana is probably right. I've done this twice, once with a "good" USB-caddy for the HDD and once with a bad one. The "good" one worked perfectly from the get-go without any hassles, and the bad one was nothing but trouble. Not the HDD, but the caddy itself. Both caddys were for serial HDD's. A third caddy from the same mfg as the bad one, but for IDE HDD's, works OK.

amenex
Offline
Iscritto: 01/03/2015

Magic Banana is probably right. I've done this twice, once with a "good"
USB-caddy for the HDD and once with a bad one. The "good" one worked
perfectly from the get-go without any hassles, and the bad one was nothing
but trouble. Not the HDD, but the caddy itself. Both caddys were for serial
HDD's. A third caddy from the same mfg as the bad one, but for IDE HDD's,
works OK.

Megver83
Offline
Iscritto: 12/21/2015

I supposed so, once from all the times I tried appeared to me a message telling me that it was probably a problem with the HDD or the CD (but it was an USB, so i laught when it said I had to clean it). But it´s strange, what kind of problem would be, if I can perfectly do the partitions with GParted? But I can assure that the problem is not the USB, so I think you are right. Can I fix that? I mean, I spent a lot of money to get it.

Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

To be sure that the disk is defective, check its SMART and self-test it. Like I wrote in my post above.

Megver83
Offline
Iscritto: 12/21/2015

This is the result, it´s in spanish:
Proper estimation: threshold not exceeded
General estimation: The disk is correct

???

Captura de pantalla de 2016-01-25 18:59:19.png
Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

Have you run the complete "autocomprobación"?

Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

Have you run the complete "autocomprobación"?

Megver83
Offline
Iscritto: 12/21/2015

This is the result

Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

To be sure that the disk is defective, check its SMART and self-test it. Like
I wrote in my post above.

Megver83
Offline
Iscritto: 12/21/2015

Wait... What? you are wizards. Now I connected my HDD and guess what. I cannot copy files without root access.
But the installation is made like the superuser?

Megver83
Offline
Iscritto: 12/21/2015

It´s a 1TB Toshiba HDD, it connects with a 3.0 usb cable. I already
installed Trisquel on a 32 GB pendrive (usb 3.0 too) and worked, so I said
"cool, now with the Toshiba external HDD" but.... as sth. had to go bad.
It´s not a problem with the partitions, but during installation in the
terminal interface that shows the progress it appears me a message like a
thousand times:

(date)(time) trisquel kernel (...) reset full speed usb device number 2 using
uhci_hcd
(date)(time) trisquel kernel (...) parent hub missing LPM exit latency info.
Power management will be impacted.

So I´m like "yea yea, bla bla...." but the progress bar stucks in the
middle.

The (...) represents some numbers without importance.

*NOTE: This same post is in the spanish forum, just put this because in the
spanish forum seems that some people have few time.

Magic Banana

I am a member!

I am a translator!

Offline
Iscritto: 07/24/2010

The HDD may be defective. You can self-test it by selecting it in "Disks" (in
the "System settings") and using the related entry in the menu (the button
with a gear in the upper-right corner of the window).

Megver83
Offline
Iscritto: 12/21/2015

I supposed so, once from all the times I tried appeared to me a message
telling me that it was probably a problem with the HDD or the CD (but it was
an USB, so i laught when it said I had to clean it). But it´s strange, what
kind of problem would be, if I can perfectly do the partitions with GParted?
But I can assure that the problem is not the USB, so I think you are right.
Can I fix that?

Megver83
Offline
Iscritto: 12/21/2015

Wait... What? you are wizards. Now I connected my HDD and guess what. I
CANNOT COPY FILES!!
But is not encrypted or sth. like that. What is it?