Trisquel linux on Raspberry Pi 3

7 risposte [Ultimo contenuto]
foffo
Offline
Iscritto: 05/14/2012

I wanted to know if Trisquel linux could be installed on Raspberry Pi 3 ?

jxself
Offline
Iscritto: 09/13/2010

Technically it could, but Trisquel is not built for ARM.

gnulux
Offline
Iscritto: 06/17/2015

According to what I’ve read, RPi isn’t open hardware, so you should really avoid it. On the contrary OlinuxIno makes open boards — this one seems rather good, is used for the Freedombox project: https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXIno-LIME2/open-source-hardware
You can install Debian (free by default) on it.

davidpgil
Offline
Iscritto: 08/26/2015

WOW! I didn't know there was another Open Hardware site! I thought all we had was Crowd Supply! Thanks for sharing this!

haudrufwienix
Offline
Iscritto: 09/02/2016

according to https://wiki.debian.org/RaspberryPi :
"A binary blob used by the GPU must be present on the SD card for the system to boot."
"Debian armhf will work (with a custom kernel)."

My understanding of this is the fully free armhf version does not work out of the box. You have to include proprietary software to be able to boot the Pi. Please correct me if I'm wrong.
Raspbian provided by the Raspberry Pi Foundation is basically Debain + 2MB huge binary bloob necessary to start + additional non-free software including Oracle Java and Wolfram Mathematica.

The Raspberry Pi is invitingly cheap but in terms of freedom it sadly comes off badly.

Here https://www.fsf.org/resources/hw/single-board-computers you can find a rating of some single-board computers concerning freedom.

I'd recommend you the Beaglebone Black. As far as I know you can run this device with only free software. The only downside of this board is the "low" computing power compared to a new Rasperry Pi.

davidpgil
Offline
Iscritto: 08/26/2015

I just found out about the Hi-Five1 an apparently Open Source
Hardware Arduino compatible microprocessor!

https://www.crowdsupply.com/sifive/hifive1

----- Original Message -----
From: name at domain
To: "trisquel-users" <name at domain>
Sent: Thursday, May 11, 2017 9:07:59 AM
Subject: Re: [Trisquel-users] Trisquel linux on Raspberry Pi 3

according to https://wiki.debian.org/RaspberryPi :
"A binary blob used by the GPU must be present on the SD card for the system
to boot."
"Debian armhf will work (with a custom kernel)."

My understanding of this is the fully free armhf version does not work out of
the box. You have to include proprietary software to be able to boot the Pi.
Please correct me if I'm wrong.
Raspbian provided by the Raspberry Pi Foundation is basically Debain + 2MB
huge binary bloob necessary to start + additional non-free software including
Oracle Java and Wolfram Mathematica.

The Raspberry Pi is invitingly cheap but in terms of freedom it sadly comes
off badly.

Here https://www.fsf.org/resources/hw/single-board-computers you can find a
rating of some single-board computers concerning freedom.

I'd recommend you the Beaglebone Black. As far as I know you can run this
device with only free software. The only downside of this board is the "low"
computing power compared to a new Rasperry Pi.

megurineturilli
Offline
Iscritto: 01/10/2012

There is an experimental free boot firmware for the RPI.

https://blog.adafruit.com/2017/01/20/blobless-linux-on-raspberry-pi-rpi-open-firmware-piday-raspberrypi-raspberry_pi/

Maybe in 5 years it will be usable in freedom, even with 3D graphics support. GCC supports the VC4 but not PowerVR.

libreleah
Offline
Iscritto: 04/03/2017

I'm not sure about Trisquel, but it might be possible to use Parabola on one. It supports BBB, which uses the same ARMv7 CPU